The Battery Show

Designed for convenient point of use drying without the need for electrical power, membrane dryers utilize hollow fiber membranes to remove water vapor from compressed air. Permeable to water vapor but not air, the IDG series can achieve pressure dew points as low as -44°F (-42°C) and ISO 8573-1 moisture classes from 2 to 6. They have no moving parts, vibration, or heat discharge and contribute only a small amount of purge air to their operating environment. The IDG series is available as single units or conveniently assembled with necessary pre-filtration and optional pressure regulation.

SMC's air preparation (FRL) products offer a wide variety of filter, regulator, and lubricator units.  Combination units include air filter regulator, air filter regulator mist separator, as well as ambient dryers, booster regulators, precision regulators, mist separators, and a wide range of accessories.

The 25A- series variations are designed using material compatible with secondary battery applications and are able to be used in low dew point environments.  The variations eliminate copper (Cu) and zinc (Zn) material where possible, making them compatible with secondary battery manufacturing for electronics, automotive, and other vehicle types.

The 25A valve series is designed using material compatible with secondary battery applications and able to be used in low dew point environments.  These variations eliminate copper (Cu) and zinc (Zn) material where possible, making them compatible with secondary battery manufacturing for electronics, automotive, and other vehicle type.

Electric linear actuators can push, pull, or transfer workloads differently than pneumatic actuators.  Pneumatic actuators rely on relatively crude devices such as rubber cushions or shock absorbers, pressure regulators, and flow restricting fittings at the port to control their motion.  By contrast, an electric actuator employs an electronically controlled motor and ballscrew to deliver a precise motion profile through acceleration, speed, and deceleration.  Further, the controller can integrate multiple "stop" positions along the actuator's stroke with high precision and repeatability.

The 25A- series variations are designed using material compatible with secondary battery applications and are able to be used in low dew point environments.  The variations eliminate copper (Cu) and zinc (Zn) material where possible, making them compatible with secondary battery manufacturing for electronics, automotive, and other vehicle types.

Air cylinders and pneumatic actuators can support automation by enhancing productivity, increasing throughput, and improving worker safety.  The 25A- series variations are designed using materials compatible with secondary battery applications, and are able to be used in low dew point environments.  These actuators range from linear, guided, rodless, locking, clamp, and stopper styles, and are available with inch and metric dimensions, and as NFPA and ISO Standards.  The line also includes related products such as shock absorbers and joints, also compatible with secondary battery applications.

SMC's 25A- Process Valve series feature air pilot/direct solenoid operated valves designed using materials compliant with secondary battery applications and are able to be used in low dew point environments.  Available body materials include resin, aluminum, brass, or stainless steel.

Industrial sensors and switches, sometimes referred to as transducers, installed in the factory automation space can provide essential machine feedback.  They can monitor On/Off status, confirm operation within an optimal range, or measure real time operation e.g. pressure or flow.

Vacuum generators are integral to industrial automation pick and place systems as gripping solutions.  SMC's array of vacuum generators, also referred to as ejectors, have variations that include single ejector unit, manifold, inline, and generator/cup in one. 

SMC one-touch tube fittings come in metric and inch size pneumatic fittings and are available in a wide variety of sizes, body styles and thread types.  The specially designed packing provides positive sealing under pressure without the reduced flow common with compression fittings.  SMC offers one-touch tube fittings in several special environments such as anti-static, flame resistant, clean room, DOT, and food service fittings.

The EX600 serial interface offers a full suite of diagnostics and programmable parameters to meet the most stringent requirements. The EX600 offers excellent flexibility including digital input, digital output and analog input unit options. With the use of D-sub output blocks, a maximum of 9 remote D-sub manifolds can be attached to one EX600 communication module. This serial interface is compatible with series SV1000/2000/3000, VQC1000/2000/4000, S0700 and the new SY series valves. Available protocols include PROFIBUS-DP®, DeviceNet™, CC-Link, Ethernet I/P™ and EtherCAT®, PROFINET, POWELINK and CC-Link IE Field™

The EX600 serial interface offers a full suite of diagnostics and programmable parameters to meet the most stringent requirements. The EX600 offers excellent flexibility including digital input, digital output and analog input unit options. With the use of D-sub output blocks, a maximum of 9 remote D-sub manifolds can be attached to one EX600 communication module. This serial interface is compatible with series SV1000/2000/3000, VQC1000/2000/4000, S0700 and the new SY series valves. Available protocols include  Ethernet/IP™, PROFINET. 

Recirculating chillers and heat exchangers are installed to provide thermal stability for applications in industrial and applied sciences from laser cutting, welding, marking and plastic injection molding. Lab science and analytical equipment applications include: mass spectrometry, gas chromatography, MRIs, CT scanners, radiation therapy machines and other medical equipment.

The HRS-R is the IP54 rated variation of our popular HRS compact recirculating chiller.  Upgrades include an IP54 electrical box and IP67 cable entries on the back panel.  Additionally, the entire paneled housing is comprised of coated metal to resist degradation from oil mist, with an available stainless steel option for greater corrosion resistance.  An optional 12L circulating coolant return tank can be selected.  This tank has a capped opening separate from the fill port for easier cleaning when necessary.  Finally, the ambient temperature upper limit has been increased to 45°C.  The HRS-R shares many features with the standard HRS, including common overall dimensions, caster wheels for mobility, an angled fill port with a level indicator for the fluid tank, and a heating function.  A magnet pump eliminates leakage and seal replacement.  The dustproof filter is removable for cleaning without tools.  The refrigerant is air cooled.  If an external PF3W flow sensor is desired, a 24VDC power supply is available at the rear.

HRS compact recirculating chillers are designed to meet the widest range of single-point applications in both industrial and technology settings. The package design is robust enough for the factory, yet ergonomic and compact for lab installations. Coolant can be either heated or cooled within the set temperature range. Choose from six cooling capacities, air or water cooled refrigerant, and global power supply options. This model is compatible with 200 VAC power.